The Complete Guide to Glycol Chiller Systems: Understanding Design, Control and Installation

Understanding Glycol Chiller Systems

Across the UK, glycol chiller systems support industries that rely on accurate temperature regulation. From food and beverage production to pharmaceutical manufacturing and industrial processing, these systems provide consistent cooling performance using a solution of glycol blended with water to transfer heat.

Unlike standard water chillers, glycol chillers use a mixture of propylene or ethylene glycol combined with water. This makes them suitable for applications operating below 0°C or installations with outdoor pipework exposed to cold weather.

At a fundamental level, glycol chiller systems extract unwanted heat via a closed refrigeration cycle. The cooled glycol solution is then pumped through pipework to absorb heat from equipment or products before returning to the chiller.

How a Glycol Chiller System Works

A well-considered glycol chiller system design supports efficiency and stable operation. Core components typically include:

• Refrigeration compressor


• Condenser


• Evaporator


• Metering device


• Integrated buffer tank and circulation pump


• Electrical control system

Within the evaporator, the refrigeration cycle removes heat from the circulating glycol solution. The chilled solution is then sent to the process load, absorbs heat, and flows back to the unit.

A typical glycol chiller system diagram shows two distinct circuits. The refrigeration loop manages heat removal, while the glycol loop transfers chilled fluid to the point of use. Accurate schematics are valuable for installation, servicing and fault finding.

Glycol Chiller System Control Panel

The glycol chiller system control panel acts as the operational centre of the system. Modern panels typically include:

• Digital temperature controllers


• PLC or microprocessor interfaces


• High and low pressure safety switches


• Pump sequencing controls


• Alarm notifications


• Remote monitoring capabilities

The control panel regulates compressor operation, maintains setpoint temperatures and monitors system pressures. Many systems also log performance data to support service planning and operational records.

In facilities requiring precise cooling, reliable control minimises fluctuations that might compromise process stability.

Control Panel Installation Considerations

Proper glycol chiller system control panel installation is essential for safe operation and long-term reliability. Key factors include:

• Electrical integration – The panel should be installed in accordance with UK standards, with correct breaker sizing and safe isolation points.


• Environmental positioning – Panels should be located in dry, well-ventilated areas away from excessive heat, vibration or moisture.


• System validation – Qualified engineers should verify sensor calibration, test alarms and confirm pressure switch operation.

Commissioning ensures the unit operates in line with the original glycol chiller system design specifications.

Key Factors in System Design

Effective glycol chiller system design begins with detailed analysis of process requirements. Engineers evaluate:

• Required temperature range


• Hydraulic design and circulation requirements


• Ambient environmental conditions


• System resilience planning


• Future expansion potential

Correct sizing is essential to avoid inefficiency or inadequate cooling. Load calculations must consider peak demand and operational cycles.

Fluid selection also plays a role. Food-related industries often favour propylene glycol for safety reasons, whereas ethylene glycol may be selected for industrial environments requiring improved heat transfer efficiency.

Additional considerations such as pipe insulation, pump specification and heat exchanger configuration influence stability, efficiency and lifespan.

Where Glycol Cooling Is Used

Glycol chiller systems support numerous sectors across the UK, including:

• Beer and spirit production


• Dairy and food processing facilities


• Pharmaceutical production environments


• Precision equipment temperature control


• Manufacturing and moulding operations


• Cold storage and preparation areas

For example, in beverage production, chillers maintain fermentation temperatures and cool storage tanks. In manufacturing settings, they prevent overheating during continuous machinery operation.

Protecting System Performance

Routine maintenance supports efficient operation and reduced downtime. Typical servicing tasks include:

• Testing fluid concentration and condition


• Inspecting pumps and seals


• Removing debris from heat rejection surfaces


• Reviewing operational parameters


• Confirming correct refrigeration performance

Over time, glycol can lose effectiveness through dilution or contamination, reducing heat transfer efficiency. Regular testing helps maintain optimal performance.

When correctly designed, installed and maintained, glycol chiller systems can provide reliable service for many years.

Common Queries About Glycol Chiller Systems

What is the typical glycol percentage?

The required percentage depends on freeze protection and operating temperature, commonly ranging from 20–40%.

Is external installation possible?

Outdoor installation is possible when the system is designed for external conditions.

What makes glycol systems different?

Unlike water-only systems, glycol-based chillers resist freezing and support sub-zero applications.

Is remote access available?

Advanced control panels often provide remote monitoring and data logging functionality.

How often should glycol fluid be tested?

Annual testing is common, though high-demand systems may require more frequent checks.

Where are they most commonly used?

Food production, beverage processing, pharmaceuticals and precision engineering rely heavily on glycol cooling.

Final Considerations

Glycol chiller systems deliver reliable and consistent temperature control across a broad range of industrial and commercial applications. From accurate load calculation and correct commissioning through to routine servicing, every stage affects efficiency and longevity.

Whether planning a new installation or upgrading existing equipment, engaging knowledgeable engineers helps align system capacity with process needs. For technical advice and tailored solutions, visit the relevant specialists at the Newsome glycol chillers page to review professionally engineered systems.